Fuji Electric Frenic lift, Справочное руководство

Страница: 17 / 254

2-4
The following tables list the function codes available for the FRENIC-Lift (LM2A) series of inverters.
 F codes: Fundamental Functions
Code Name Data setting range
Incr
em
ent
Un
it
Ch
a
n
ge
wh
en
runni
ng
Da
ta
cop
yin
g
Default s
e
ttin
g
Data f
o
rm
a
t No.
To
rq
ue v
e
ctor
control
Softw
ar
e ver
si
o
n
wh
ich
ca
n b
e
used
F00 Data Protection 0: Disable data protection
(Function code data can be edited)
1: Enable data protection
Note: This setting is effective if H99 = 0000
H
.
- - Y N 0 1 Y
(Password entry) 0001
H
to FFFF
H
Note: This setting is effective if H99 = other than 0000
H
.
Data of H99 is your password
F01 Frequency Command 0: Multistep speed command ( SS1 , SS2 , SS4 , SS8 )
1: Analog speed command (Not reversible)
2: Analog speed command (Reversible)
3: Analog multistep speed command
- - N Y 0 1 Y
F03 Rated speed 30.0 to 6000
*1
(Equivalent with 1.00 to 200.00 Hz) Variable r/min N Y 1450
*2
37 Y
F04 Base speed 30.0 to 6000
*1
(Equivalent with 1.00 to 200.00 Hz) Variable *3 N Y 1500 37 Y
F05 Rated Voltage 80 to 240 (for 200 V class series) 1 V N Y2 230 1 Y
160 to 500 (for 400 V class series) 380
F07 Acceleration/Deceleration Time 1 0.00 to 99.9
Note: Acceleration/Deceleration time is ignored at 0.00. Variable s Y Y 1.80 12 Y
F08 Acceleration/Deceleration Time 2 Variable s Y Y 1.80 12 Y
F09 Torque boost 0.0 to 5.0 0.1 - Y Y *9 3 Y
*8
F10 Electronic Thermal Overload Protection
for Motor
(Select motor characteristics)
1: For general-purpose motors with built-in self-cooling fan
2: For inverter-driven motors or high-speed motors with
forced-ventilation fan
3: For general-purpose motors with built-in self-cooling fan
(Mode2)
- - Y Y 2 1 Y
500
F11 (Overload detection level) OFF (0.00): Disable
1 to 200% of the rated current (allowable continuous drive
current) of the inverter Variable A Y Y1 Y2 Refer to
default
table
24 Y
F12 (Thermal time constant) 0.5 to 75.0 0.1 min Y Y 2.0 3 Y
F20 DC Braking (Starting Speed) 0.00 to 150.0
*1
(Equivalent with 0.00 to 5.00 Hz) Variable *3 N Y 0.0 37 Y
*8
F21 (Braking Level) 0 to 100 1 % N Y 0 1 Y
*8
F22 (Braking Time) OFF (0.00): Disable
0.01 to 30.00
0.01 s N Y OFF 5 Y
*8
F23 Starting Speed 0.00 to 150.0
*1
(Equivalent with 0.00 to 5.00 Hz) Variable *3 N Y 0.00 37 Y
F24 (Holding time) 0.00 to 10.00 0.01 s N Y 0.80 5 Y
F25 Stop Speed 0.00 to 150.0
*1
(Equivalent with 0.00 to 5.00 Hz) Variable *3 N Y 3.00 37 Y
F26 Motor Sound (Carrier frequency) 5 to 16 1 kHz N Y 15 1 Y
F30 FMA Terminal (Output gain) 0 to 300 1 % Y Y 100 1 Y
F31 (Function selection) - - Y Y 0 1 -
0: Reference speed (Final) Y
1: Primary frequency Y
2: Output current Y
3: Output voltage Y
4: Output torque Y
8: Actual speed N
9: DC link bus voltage Y
10: Universal AO Y
14: Calibration (+) Y
18: Inverter heat sink temperature Y
19: Inverter internal temperature Y
111: Customizable logic output signal 1
to
120: Customizable logic output signal 10 Y
F42 Control Mode 0: Vector control with PG for asynchronous motor
1: Vector control with PG for synchronous motor
2: Torque vector control - - N Y 0 1 Y
F44 Current Limiter (Level) Auto(32767): Maximum current of each inverter automatically
applies.
100 to 230 (Percentage to the rated current of the inverter) 1 % Y Y Auto 1 N
F50 Electronic thermal overload protection
for braking resistor
(Discharging
capacity)
OFF(32767): Disable
1 to 9000 1 kWs Y Y1 Y2 OFF 1 Y
F51 (Allowable average loss) 0.001 to 99.99 Variable kW Y Y1 Y2 0.001 45 Y
F52 (Resistance) None(0.00): Not applicable
0.01 to 999 Variable Ohm Y Y1 Y2 None 12 Y
*1 The data setting range is variable. Refer to Section 2.2.
*2 The factory default setting varies depending on the shipping destination.
*3 The unit changes depending on the setting of C21.
*8 This function code is only for the torque vector control.
*9 FRN0025LM2A-4_ (11kW) to FRN0045LM2A-4_ (22kW): 0.3
Other: 0.0.