Siemens SINUMERIK 840D sl Function Manual Download Page 848 | Manualshive

Page: 848 / 2184

background image

Detailed description

2.4 Frames

Basic logic functions: Axes, coordinate systems, frames (K2)

64

Function Manual, 11/2006, 6FC5397-0BP10-2BA0

2.4.3.3

NCU global frames

All settable frames

G54

to

G599

and all basic frames can be configured NCU globally or

channel-specifically. A combination of these is also possible with basic frames. Global

frames affect all channels on an NCU. All channels have read and write access to the NCU.

Global frames only have axial frame components, such as translations, scales and mirrors of

individual axes. Each channel can read or modify global frames for any machine axis.
A characteristic of global frames is that they are calculated in all channels of an NCU. As the

assignment of machine axes to channel axes and, in particular, to geometry axes, can be

different in all channels, there is no geometric relationship. Global frames describe offsets,

scales and mirrors of machine axes. Rotations cannot be used on global frames.
All settable frames can be reconfigured to global frames with the following machine data:
MD18601 $MN_MM_NUM_GLOBAL_USER_FRAMES (number of global, pre-defined user

frames (SRAM))
If the value of this machine data is greater than zero, there are no channel-specific settable

frames.
The following machine data becomes irrelevant then, and is not evaluated:
MD28080 $MC_MM_NUM_USER_FRAMES (number of settable frames (SRAM))
The number of global basic frames is parameterized through the following machine data:
MD18602 $MN_MM_NUM_GLOBAL_BASE_FRAMES (number of global, basic frames

(SRAM))
Channel-specific basic frames can also exist simultaneously through the following machine

data:
MD28081 $MC_MM_NUM_BASE_FRAMES (number of basic frames (SRAM))
Global frames can be read and written from all channels of an NCU. When writing global

frames, the user must ensure channel coordination. This can be achieved through e.g., wait

markers.

2.4.4

Frame chain and coordinate systems

2.4.4.1

Overview

The figure below shows the frame chain for the current complete frame. The frame chain is

stored between the BCS and WCS. The SZS (Settable Zero System) corresponds to the

WCS, transformed by the programmable frame. The BZS (Basic Zero System) still includes

the current settable frame. The system frame for the zero offset external is only available if it

has been configured, otherwise the zero offset external is interpolated as a superimposed

motion of the axis, as it has been up to this point.

«
...
846
847
848
849
850
...
»

Summary of Contents for SINUMERIK 840D sl









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 840D sl

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Garmin Pages: 12

Brand: JDS Uniphase Pages: 27

Brand: Danfoss Pages: 20

Brand: OEG Pages: 168

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

1E0671-1 MCR2.9

Brand: Haberl Electronic Pages: 9

Brand: J+J Pages: 2

Brand: Linear Technology Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands