Renesas RX600 Series User Manual Download Page 622 | Manualshive

Page: 622 / 1006

background image

RX610 Group

20. Serial Communications Interface (SCI)

R01UH0032EJ0120 Rev.1.20

Page 622 of 1006

Feb 20, 2013

(2) Smart Card Interface Mode (SMIF in SCMR = 1)

Addresses: SCI0.SCR 0008 8242h, SCI1.SCR 0008 824Ah, SCI2.SCR 0008 8295h, SCI3.SCR 0008 25Ah

SCI4.SCR 0008 8262h, SCI5.SCR 0008 826Ah, SCI6.SCR 0008 8272h

b7

b6

b5

b4

b3

b2

b1

b0

Value after reset:

0

0

0

0

0

0

0

0

TIE

RIE

TE

RE

—

TEIE

CKE[1:0]

Bit

Symbol

Bit Name

Function

R/W

b1, b0

CKE[1:0]

Clock Enable

•

When GM in SMR = 0

b1 b0

0 0: Output disabled (SCKn pin functions as I/O port.)

0 1: Clock output

1 0: Setting prohibited

1 1: Setting prohibited

•

When GM in SMR = 1

0 0: Output fixed low

0 1: Clock output

1 0: Output fixed high

1 1: Clock output

R/W

*

1

b2

TEIE

Transmit End Interrupt Enable

This bit should be 0 in smart card interface mode.

R/W

b3



Reserved

This bit is read as 0. The write value should be 0.

R/W

b4

RE

Receive Enable

0: Serial reception is disabled

1: Serial reception is enabled

R/W

*

2

b5

TE

Transmit Enable

0: Serial transmission is disabled

1: Serial transmission is enabled

R/W

*

2

b6

RIE

Receive Interrupt Enable

0: RXI and ERI interrupt requests are disabled

1: RXI and ERI interrupt requests are enabled

R/W

b7

TIE

Transmit Interrupt Enable

0: A TXI interrupt request is disabled

1: A TXI interrupt request is enabled

R/W

Notes: 1. Writable only when TE = 0 and RE = 0.

2. A 1 can be written only when TE = 0 and RE = 0. After setting TE or RE to 1, only 0 can be written in TE and RE.

SCR is a register that enables/disables the SCI transfer operations and selects the transfer clock source. For details on
interrupt requests, see 20.6, Interrupt Sources.

CKE[1:0] Bits (Clock Enable)

These bits control the clock output from the SCKn pin.

In GSM mode, clock output can be dynamically switched. For details, see section 20.5.8, Clock Output Control.

TEIE Bit (Transmit End Interrupt Enable)

This bit should be 0 in smart card interface mode.

«
...
620
621
622
623
624
...
»

Summary of Contents for RX600 Series















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX600 Series

Brand: Xinje Pages: 57

Brand: Alcad Pages: 6

Brand: Idis Pages: 31

Brand: Supermicro Pages: 16

Brand: T.A Pages: 11

PARTNER PC CARD

Brand: Avaya Pages: 4

Brand: Eaton Pages: 14

Brand: Accusys Pages: 34

Soundweb 9088ii DSP System

Brand: BSS Audio Pages: 2

Brand: NEC Pages: 47

H8S/2615 Series

Brand: Renesas Pages: 28

Brand: Jabra Pages: 2

Brand: Vivotek Pages: 185

Network Video Recorder

Brand: IC Realtime Pages: 118

Mobile Network Video Recorder

Brand: IC Realtime Pages: 158

Campus BridgeLINK

Brand: RadioLAN Pages: 146

Brand: Bosch Pages: 28

Brand: Bosch Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands