Renesas RX600 Series User Manual Download Page 256

Page: 256 / 1006

RX610 Group

11. Buses

R01UH0032EJ0120 Rev.1.20

Page 256 of 1006

Feb 20, 2013

11.

Buses

11.1

Overview

Table 11.1 lists the bus specifications and figure 11.1 shows the bus configuration.

Table 11.1 Bus Specifications

Bus Type

Description

CPU bus

Instruction bus

•

Connected to the CPU (for instructions)

•

Connected to on-chip memory (on-chip RAM, on-chip ROM)

•

Operates in synchronization with the system clock (ICLK)

Operand bus

•

Connected to the CPU (for operands)

•

Connected to on-chip memory (on-chip RAM, on-chip ROM)

•

Operates in synchronization with the system clock (ICLK)

Internal main bus

Internal main bus 1

•

Connected to the CPU

•

Operates in synchronization with the system clock (ICLK)

Internal main bus 2

•

Connected to the DMAC and DTC

•

Connected to on-chip memory (on-chip RAM, on-chip ROM)

•

Operates in synchronization with the system clock (ICLK)

Internal peripheral

bus

Internal peripheral bus 1

•

Connected to peripheral modules

•

Operates in synchronization with the system clock (ICLK)

Internal peripheral bus 2

•

Connected to peripheral modules, on-chip ROM (for programming and

erasure), and data-flash memory

•

Operates in synchronization with the peripheral-module clock (PCLK)

External bus

•

Connected to the external devices

•

Operates in synchronization with the external-bus clock (BCLK)

Peripheral

function

Bus error monitoring

section

CPU

Internal main bus 1

Peripheral

func ion

Internal main bus 2

External bus

control

Instruction bus

Operand bus

On-chip

ROM

On-chip

RAM

Internal peripheral bus 1

Internal peripheral bus 2

Peripheral

function

DMAC(

Note: DMAC(

m) is used for bus mastership, while DMAC(

s) is for register access.

ICLK synchronization

BCLK synchronization

PCLK
synchronization

Write buffer

External bus

DTC

DMAC(

Data flash

Figure 11.1 Bus Configuration

Summary of Contents for RX600 Series















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX600 Series

Reviews:

Related manuals for RX600 Series

Brands by name

Popular brands

Renesas RX600 Series, User Manual

Search results

Summary of Contents for RX600 Series

Reviews:

Related manuals for RX600 Series

Brands by name

Popular brands