manualshive.com logo in svg

Mitsubishi Electric MELSERVO-MR-J4 GF Series, Instruction Manual

The Mitsubishi Electric MELSERVO-MR-J4 GF Series Instruction Manual is available for free download on our website. This comprehensive manual provides detailed instructions for effectively operating and maintaining your MELSERVO-MR-J4 GF Series product. Simply visit manualshive.com to access your digital copy and unlock the full potential of your Mitsubishi Electric device.

Share
Download
background image

10  OBJECT DICTIONARY

10.3  Object dictionary details (objects in the 2000s)

279

10

 • Bit definition of control DI2

 • Bit definition of control DI3

Bit

Symbol

Description

0

The value at reading is undefined. Set "0" when writing.

1

2

3

4

5

C_CAMC

Cam control command
Turn CAMC on to switch the control from the normal positioning control to the cam control.

6

The value at reading is undefined. Set "0" when writing.

7

8

C_PC

Proportional control (PID control)
Turn C_PC on to switch the speed amplifier from the proportional integral type to the proportional type.
If the servo motor at a stop is rotated even for a pulse due to any external factor, it generates torque to compensate for a 
position mismatch. When the servo motor shaft is to be locked mechanically after positioning completion (stop), switching 
on the C_PC upon positioning completion will suppress the unnecessary torque generated to compensate for a position 
mismatch.
When the shaft is to be locked for a long time, use the C_PC and torque limit at the same time to make the torque less 
than the rated torque.

9

The value at reading is undefined. Set "0" when writing.

10

11

C_CLTC

Clutch command
This is used to turning on/off the main shaft clutch command. This is used when [Cam control data No. 36 - Main shaft 
clutch control setting] is set to "_ _ _ 1".

12

The value at reading is undefined. Set "0" when writing.

13

C_CPCD

Cam position compensation request
Turn C_CPCD on to compensate the cam axis current value per cycle to be in the position set in [Cam control data No. 60 
- Cam position compensation target position].

14

The value at reading is undefined. Set "0" when writing.

15

C_ORST

Operation alarm reset
Turn C_ORST on from off to reset [AL. F4 Positioning warning].

Bit

Symbol

Description

0

The value at reading is undefined. Set "0" when writing.

1

2

3

4

5

6

7

8

9

10

11

C_CR

Clear
Turning on C_CR clears the droop pulses in the position control counter and command remaining distance at the rising 
edge. Set the pulse width to 10 ms or longer.
If "CR (Clear) Selection" of [Pr. PD42] is set to "1", the droop pulses and command remaining distance will be always 
cleared while C_CR is on.
This bit is available with servo amplifier with software version A7 or later.

12

The value at reading is undefined. Set "0" when writing.

13

14

15

Summary of Contents for MELSERVO-MR-J4 GF Series





















































































































































































































































































































Reviews:

No comments

Related manuals for MELSERVO-MR-J4 GF Series

NAD 319 Specification Sheet preview
319
Brand: NAD Pages: 2
E&I A 1000 Manual preview
A 1000
Brand: E&I Pages: 13
JBL 6290 Manual preview
6290
Brand: JBL Pages: 30
A and T Labs K6 Assembly Manual preview
K6
Brand: A and T Labs Pages: 44
dbx 286 S Quick Manual preview
286 S
Brand: dbx Pages: 2
NAD 911 Owner'S Manual preview
911
Brand: NAD Pages: 28
HAMTRONICS LPA 2-25R Assembly, Installation, & Maintenance preview
LPA 2-25R
Brand: HAMTRONICS Pages: 5
ZABKZ P.A. Series Owner'S Manual preview
P.A. Series
Brand: ZABKZ Pages: 4
Kollmorgen Seidel SERVOSTAR 600 Series Assembly, Installation And Commissioning Instructions preview
SERVOSTAR 600 Series
Brand: Kollmorgen Seidel Pages: 68
Peavey Studio Pro 110 Operating Manual preview
Studio Pro 110
Brand: Peavey Pages: 15
Cyrus integrated 6 vs2 User Instructions preview
integrated 6 vs2
Brand: Cyrus Pages: 7
ValveTrain Amplification ValveTrain 315 User Manual preview
ValveTrain 315
Brand: ValveTrain Amplification Pages: 7
Fender 021-5700-000 Service Manual preview
021-5700-000
Brand: Fender Pages: 18
DAPAudio IPS-AM Manual preview
IPS-AM
Brand: DAPAudio Pages: 14
Supertech instruments LinearAmp User Manual preview
LinearAmp
Brand: Supertech instruments Pages: 6
McHammer Hurricane-1500 User Manual preview
Hurricane-1500
Brand: McHammer Pages: 3
MTS Systems MPA-03 SL Manual preview
MPA-03 SL
Brand: MTS Systems Pages: 22
Texas Instruments TPA3200D1 User Manual preview
TPA3200D1
Brand: Texas Instruments Pages: 13

Brands by name

Popular brands

Load more brands