Dodge 2014 Ram 1500 Owner'S Manual Download Page 175 | Manualshive

Page: 175 / 360

background image

•

Water In Fuel Indicator Light — Diesel Only

The “Water In Fuel Indicator Light” will illu-
minate when there is water detected in the fuel
filters. If this light remains on, DO NOT start
the vehicle before you drain the water from the

fuel filters to prevent engine damage. Refer to “Mainte-
nance Procedures/Draining Fuel/Water Separator Fil-
ters” in “Maintaining Your Vehicle” for further
information.

•

Wait To Start Light — Diesel Only

The “Wait To Start” telltale will illuminate for
approximately two seconds when the ignition is

turned to the RUN position. It’s duration may be longer
based on colder operating conditions. Vehicle will not
initiate start until telltale is out. Refer to “Starting Proce-
dures” in “Starting And Operating” for further
information.

NOTE:

The “Wait To Start” telltale may not illuminate if

the intake manifold temperature is warm enough.

•

Low Diesel Exhaust Fluid Light — Diesel Only

This telltale will turn on to indicate the Diesel
Exhaust Fluid (DEF) is low.

6. EVIC Red Telltales

•

Door Ajar

This light will turn on to indicate that one or
more doors may be ajar.

•

Oil Pressure Warning Light

This telltale indicates low engine oil pressure. If
the light turns on while driving, stop the vehicle

and shut off the engine as soon as possible. A chime will
sound when this light turns on.

3

UNDERSTANDING YOUR INSTRUMENT PANEL

173

«
...
173
174
175
176
177
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Kargo Master Pages: 6

Brand: Daihatsu Pages: 41

Brand: Daihatsu Pages: 268

Brand: Ford Pages: 37

Brand: V8 equipment Pages: 17

Brand: Nav TV Pages: 3

Brand: EZTRUNK Pages: 3

Brand: Whispbar Pages: 14

Ride-Rite Air Helper Springs 2173

Brand: Firestone Pages: 4

Brand: Nav TV Pages: 4

Brand: Horn Tools Pages: 12

Brand: BMW Pages: 40

Brand: Car-Interface Pages: 23

Brand: Laser Pages: 3

Brand: Cadillac Pages: 508

Brand: Kia Pages: 289

Brand: Mazda Pages: 38

M-RK 344A4616P1

Brand: Ericsson Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands