Dodge 2014 Ram 1500 Owner'S Manual Download Page 223 | Manualshive

Page: 223 / 360

background image

Cooling System Tips — Automatic Transmission

To reduce potential for engine and transmission over-
heating in high ambient temperature conditions, take the
following actions:

•

City Driving —

When stopped, shift the transmission into NEUTRAL
and increase engine idle speed.

•

Highway Driving —

Reduce your speed.

•

Up Steep Hills —

Select a lower transmission gear.

•

Air Conditioning —

Turn it off temporarily.

Do Not Operate The Engine With Low Oil Pressure

When the engine is at normal operating temperature, the
minimum oil pressures required are:

Idle 700 to 800 RPM

10 psi (69 kPa)

Full speed and load

30 psi (207 kPa)

CAUTION!

If oil pressure falls to less than normal readings, shut
the engine off immediately. Failure to do so could
result in immediate and severe engine damage.

Do Not Operate The Engine With Failed Parts

All engine failures give some warning before the parts
fail. Be on the alert for changes in performance, sounds,
and visual evidence that the engine requires service.
Some important clues are:

•

engine misfiring or vibrating severely

4

STARTING AND OPERATING

221

«
...
221
222
223
224
225
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Camcar Pages: 6

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Toyota Pages: 371

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: RAM Pages: 616

Brand: Nav TV Pages: 9

Brand: Honda Pages: 81

Brand: AEM Pages: 27

Brand: Black Horse Off Road Pages: 7

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brand: Dometic Pages: 24

F-250 Super Duty 2022

Brand: Ford Pages: 740

Giulietta 2.0 JTDM

Brand: Alfa Romeo Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands