Dodge 2014 Ram 1500 Owner'S Manual Download Page 211 | Manualshive

Page: 211 / 360

background image

CAUTION!

Do not crank engine for more than 15 seconds at a
time or starter motor damage may result. Turn the
ignition switch to the OFF position and wait at least
two minutes for the starter to cool before repeating
start procedure.

5. When the engine starts, release the key fob.

6. Check that the oil pressure warning light has turned

off.

7. Release the parking brake.

Starting Procedure — Engine Manifold Air
Temperature 0°F To 66°F (–18°C to 19°C)

NOTE:

The temperature displayed in the Electronic

Vehicle Information Center (EVIC) does not necessarily
reflect the engine manifold air temperature. Refer to
“Electronic Vehicle Information Center (EVIC)” in “Un-
derstanding Your Instrument Panel” for further informa-
tion. When engine temperatures fall below 66°F (19°C)
the “Wait To Start Light” will remain on indicating the
intake manifold heater system is active.

Follow the steps in the “Normal Starting” procedure
except:

1. The “Wait To Start” telltale will remain on for a period

of time that varies depending on the engine tempera-
ture.

4

STARTING AND OPERATING

209

«
...
209
210
211
212
213
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

Brand: EUFAB Pages: 12

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Thule Pages: 8

Brand: Subaru Pages: 21

Brand: Toyota Pages: 52

Brand: Kuda Pages: 3

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: Mercedes-Benz Pages: 358

Brand: iArmor Pages: 6

Brand: Subaru Pages: 540

Brand: Mercedes-Benz Pages: 296

Brand: Xingyun Pages: 74

Brand: Yakima Pages: 11

2011 Camry SE V6

Brand: Toyota Pages: 33

Brand: Xpresskit Pages: 12

Performer-Plus 2172

Brand: Edelbrock Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands