Dodge 2014 Ram 1500 Owner'S Manual Download Page 105 | Manualshive

Page: 105 / 360

background image

mark. The total capacity from the MIN mark to the MAX
mark is 1.3 qts (1.2 L).

CAUTION!

Overfilling or underfilling the crankcase will cause
oil aeration or loss of oil pressure. This could damage
your engine.

NOTE:

It is possible for your oil level to be slightly

higher than a previous check. This would be due to diesel
fuel that may temporarily be in the crankcase due to
operation of the diesel particulate filter regeneration
strategy. This fuel will evaporate out under normal
operation.

Never operate the engine with oil level below the “MIN”
mark or above the upper “MAX” mark.

Change Engine Oil

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

Engine Oil Viscosity (SAE Grade)

CAUTION!

Your vehicle is equipped with an advanced technol-
ogy Diesel Engine and an emission device designed
to limit Diesel Particulate Emissions from being
released into the atmosphere. The durability of your
engine and life expectancy of this diesel particulate
filter emission device is highly dependent on the use
of the correct engine oil.

5

MAINTAINING YOUR VEHICLE

103

«
...
103
104
105
106
107
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Back View Pages: 168

Brand: Harbor Freight Tools Pages: 4

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 209

Brand: VBC Racing Pages: 34

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 2

Brand: Vauxhall Pages: 236

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Actia Pages: 37

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: TATA Motors Pages: 159

Brand: NavLinkz Pages: 21

Brand: JKS Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands