Dodge 2014 Ram 1500 Owner'S Manual Download Page 338 | Manualshive

Page: 338 / 360

background image

NOTE:

•

Under no circumstances should oil change intervals
exceed 15,000 miles (24,000 km) or six months or 500
Hours, whichever comes first.

•

Replace the engine oil and oil filter every 12,500 miles
(20 000 km) when running B20 fuel (Chassis Cab
Only).

If Chassis Cab models are operated with greater than 5%
levels of Biodiesel, the oil change interval must not
exceed 12,500 miles (20 000 km) under any circumstances.
See the Fuel Requirements section for more information
regarding operation of Chassis Cab models configured
for use with Biodiesel blend (B6-B20) fuel meeting ASTM
specification D-7467.

Perform Service Indicator — Cummins® Diesel

Your vehicle will require emissions maintenance at a set
interval. To help remind you when this maintenance is
due, the Electronic Vehicle Information Center (EVIC) will
display “Perform Service”. When the “Perform Service”
message is displayed on the EVIC it is necessary to have
the emissions maintenance performed. Emissions mainte-
nance may include replacing the Closed Crankcase Ven-
tilation (CCV) filter element. The procedure for clearing
and resetting the “Perform Service” indicator message is
located in the appropriate Service Information.

336

MAINTENANCE SCHEDULE

«
...
336
337
338
339
340
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: GARO Pages: 2

AAB-P-RZR900-K2-001

Brand: SuperATV Pages: 3

Brand: Renault Pages: 238

Brand: Hella Pages: 21

Brand: NanoCam Plus Pages: 32

Brand: Scion Pages: 24

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: rough country Pages: 4

Interlock 700 Series

Brand: Scania Pages: 82

Brand: OHIOSTEEL Pages: 2

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Toyota Pages: 36

Sprinter Bed System DIY

Brand: FVC Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands