Dodge 2014 Ram 1500 Owner'S Manual Download Page 64 | Manualshive

Page: 64 / 360

background image

3. The system will automatically engage the starter to

crank the engine. If the vehicle fails to start, the starter
will disengage automatically after 30 seconds.

4. If you wish to stop the cranking of the engine prior to

the engine starting, press the button again.

5. Check that the oil pressure warning light has turned

off.

6. Release the parking brake.

Extreme Cold Weather

The engine block heater is a resistance heater installed in
the water jacket of the engine. It requires a 110–115 Volt
AC electrical outlet with a grounded, three-wire exten-
sion cord. Its use is recommended for environments that
routinely fall below -10°F (-23°C). It should be used when
the vehicle has not been running overnight or longer

periods and should be plugged in two hours prior to
start. Its use is required for cold starts with temperatures
under -20°F (-28°C).

NOTE: The engine block heater cord is a factory in-
stalled option. If your vehicle is not equipped, heater
cords are available from your authorized MOPAR®
dealer.

•

A 12 Volt heater built into the fuel filter housing aids in
preventing fuel gelling. It is controlled by a built-in
thermostat.

•

A Diesel Pre-Heat system both improves engine start-
ing and reduces the amount of white smoke generated
by a warming engine.

Starting Fluids

The engine is equipped with a glow plug preheating
system. If the instructions in this manual are followed,

62

STARTING AND OPERATING

«
...
62
63
64
65
66
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Accel Pages: 2

Brand: VEAP SHIELD UNITED Pages: 3

Brand: OEM Tools Pages: 4

Brand: Kia Pages: 385

Brand: Yakima Pages: 8

Brand: FormFit Pages: 4

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: ECS Electronics Pages: 16

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: Cadillac Pages: 407

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands