Dodge 2014 Ram 1500 Owner'S Manual Download Page 296 | Manualshive

Page: 296 / 360

background image

Oils with a high ash content may produce damaging
deposits on cylinder head valves and/or aftertreatment
system damage. A maximum sulfated ash content of 1.00
mass % is recommended for all oil used in the engine.

The same oil change interval is to be followed for
synthetic oil as for petroleum based oil. Also, synthetic oil
must meet the same performance specifications as petro-
leum oil.

CAUTION!

Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is
not covered by the New Vehicle Limited Warranty.

Engine Oil Viscosity (SAE Grade)

In ambient temperatures above 0°F (-18°C), we recom-
mend you use SAE 15W-40 engine oil such as MOPAR,
Shell Rotella and Shell Rimula that meets FCA US

Material Standard MS-10902 and the API CJ-4 engine oil
category is required. Products meeting Cummins CES
20081 may also be used. The identification of these
engine oils is typically located on the back of the oil
container.

In ambient temperatures below 0°F (-18°C), SAE 5W-40
we recommend you use

synthetic

engine oil such as

MOPAR, Shell Rotella and Shell Rimula that meets FCA
US Material Standard MS-10902 and the API CJ-4 engine
oil category is required.

CAUTION!

Failure to use SAE 5W-40 synthetic engine oil in
ambient temperatures below 0°F (-18°C) could result
in severe engine damage.

294

MAINTAINING YOUR VEHICLE

«
...
294
295
296
297
298
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Gemineye EC2014-C

Brand: Ecco Pages: 10

Reflex 5500 Series

Brand: Ecco Pages: 12

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: GOgroove Pages: 9

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

1973 Crown Hardtop

Brand: Toyota Pages: 50

Brand: Tessera4x4 Pages: 20

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: TOPPOINT Pages: 2

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

Brand: Acura Pages: 7

Brand: Jaeger Pages: 16

Brand: Roadmaster Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands