Dodge 2014 Ram 1500 Owner'S Manual Download Page 208 | Manualshive

Page: 208 / 360

background image

Follow the steps in the “Normal Starting” procedure
except:

1. Pushing the engine start button with the driver’s foot

on the brake will move the ignition from OFF or ACC
to RUN, and will illuminate the

⬙

Wait To Start

⬙

telltale.

The engine will not immediately crank, this is normal
operation.

2. The “Wait To Start

⬙

telltale will remain on for a period

of time that varies depending on the engine tempera-
ture.

3. While the

⬙

Wait to Start

⬙

telltale is on, the EVIC will

additionally display a gauge or bar whose initial
length represents the full

⬙

Wait to Start

⬙

time period.

Its length will decrease until it disappears when the

⬙

Wait to Start

⬙

time has elapsed.

CAUTION!

If the “Water in Fuel Indicator Light” remains on, DO
NOT START engine before you drain the water from
the fuel filters to avoid engine damage. Refer to
“Maintenance Procedures/Draining Fuel/Water Sepa-
rator Filter” in “Maintaining Your Vehicle” for fur-
ther information.

4. After the engine “Wait To Start” telltale goes off, the

engine will automatically crank.

CAUTION!

The engine may automatically crank when the “Wait
To Start” time has elapsed. To abort the automatic
starting process, ensure the driver’s foot is fully
removed from the brake pedal prior to pushing the
START/STOP button to cycle the ignition off.

206

STARTING AND OPERATING

«
...
206
207
208
209
210
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: FormFit Pages: 2

Brand: Mercedes-Benz Pages: 368

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Ford Pages: 40

Brand: BMW Pages: 64

Cuda TriOptic 351014F Series

Brand: Federal Signal Corporation Pages: 4

Brand: Kia Pages: 216

Brand: Yakima Pages: 10

Brand: Yakima Pages: 10

Brand: WABCO Pages: 40

Truck 2500 2018

Brand: RAM Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands