Dodge 2014 Ram 1500 Owner'S Manual Download Page 320 | Manualshive

Page: 320 / 360

background image

Selection of Lubricant

Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for fluid specifications.

Fluid Level Check

This fluid level can be checked by removing the filler
plug. The fluid level should be to the bottom edge of the
filler plug hole with the vehicle in a level position.

Manual Transmission — If Equipped

Selection of Lubricant

Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for fluid specifications.

Fluid Level Check

The fluid level can be checked by removing the filler
plug. If the level of the lubricant is more than 1/2 in (12
mm) below the bottom of the filler hole while the vehicle

is on level ground, enough lubricant should be added to
bring the level to 1/4 in (6 mm) below the bottom of the
filler hole.

Automatic Transmission — If Equipped

Selection of Lubricant

It is important to use the proper transmission fluid to
ensure optimum transmission performance and life. Use
only the manufacturer’s specified transmission fluid.
Refer to “Fluids, Lubricants, and Genuine Parts” in this
section for fluid specifications. It is important to maintain
the transmission fluid at the correct level using the
recommended fluid.

No chemical flushes should be used in any transmission;
only the approved lubricant should be used.

318

MAINTAINING YOUR VEHICLE

«
...
318
319
320
321
322
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Camcar Pages: 2

Brand: Actia Pages: 37

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: Quadratec Pages: 14

Brand: Saturn Pages: 440

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: JSPORT Pages: 2

Brand: Honda Pages: 24

Brand: ROADGEAR Pages: 2

Brand: WABCO Pages: 224

Brand: Conrad Pages: 8

Brand: MovaNext Pages: 4

Brand: Alu-Cab Pages: 6

Brand: Dodge Pages: 439

Brand: Ferrari Pages: 45

Brand: Improved Racing Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands