Dodge 2014 Ram 1500 Owner'S Manual Download Page 249 | Manualshive

Page: 249 / 360

background image

NOTE:

For application specific information with respect

to PTO and pump requirements and additional vehicle
information (wiring schematics, preset idle values, en-
gine speed limits, and vehicle hardware and software
requirements) please refer to the Body Builders Guide by
accessing

www.rambodybuilder.com

and choosing the

appropriate links.

Power Take Off — Aftermarket Installation

If you did not order the PTO (Power Take Off) Prep
Package from the factory and want to convert your
vehicle,

refer

to

the

Body

Builder’s

Guide

at

www.rambodybuilder.com

or contact the manufacturer

directly at (866) 205–4102 (toll free).

ENGINE RUNAWAY

Diesel engine runaway is a rare condition affecting diesel
engines, where the engine consumes its own lubrication
oil and runs at higher and higher RPM until it overspeeds

to a point where it destroys itself due to either mechani-
cal failure or engine seizure through lack of lubrication.

WARNING!

In case of engine runaway due to flammable fumes
from fuel spills or turbocharger oil leaks being
sucked into the engine, do the following to help
avoid personal injury and/or vehicle damage:
1. Turn the ignition switch to the OFF position.
2. Using a CO2 or dry chemical type fire extinguisher,
direct the spray from the fire extinguisher into the
grille on the passenger side so that the spray enters
the engine air intake.
The inlet for the engine air intake is located behind
the passenger side headlamp and receives air
through the grille.

4

STARTING AND OPERATING

247

«
...
247
248
249
250
251
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: GMC Pages: 20

Brand: TATA Motors Pages: 156

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Brand: Cadillac Pages: 522

Brand: TATA Motors Pages: 236

Brand: Van Guard Pages: 3

Brand: Ford Pages: 8

Brand: Intec Pages: 16

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Skoda Pages: 281

Brand: Subaru Pages: 44

Brand: BrandMotion Pages: 12

Brand: Dacia Pages: 244

XEV1R22T2 Series

Brand: hager Pages: 14

Brand: WALMEC Pages: 6

Brand: Seecode Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands