Dodge 2014 Ram 1500 Owner'S Manual Download | Manualshive

Page: 322 / 360

background image

Use the following procedure to check the transmission
fluid level properly:

1. Monitor the transmission temperature using the EVIC

display, and operate the vehicle as required to reach
the normal operating temperature.

2. Park the vehicle on level ground.

3. Run the engine at normal idle speed for at least 60

seconds, and leave the engine running for the rest of
this procedure.

4. Fully apply the parking brake and press the brake

pedal.

5. Place the shift lever momentarily into each gear posi-

tion (allowing time for the transmission to fully en-
gage in each position), ending with the transmission in
PARK.

6. Remove the dipstick, wipe it clean and reinsert it until

seated.

7. Remove the dipstick again and note the fluid level on

both sides. The fluid level reading is only valid if there
is a solid coating of oil on both sides of the dipstick.
Note that the holes in the dipstick will be full of fluid
if the actual level is at or above the hole. The fluid level
should be between the “HOT” (upper) reference holes
on the dipstick at normal operating temperature. If the
fluid level is low, add fluid through the dipstick tube
to bring it to the proper level.

Do not overfill.

Use

ONLY the recommended fluid (see

⬙

Fluids, Lubri-

cants, and Genuine Parts

⬙

for fluid specifications).

After adding any quantity of oil through the dipstick
tube, wait a minimum of two minutes for the oil to
fully drain into the transmission before rechecking the
fluid level.

320

MAINTAINING YOUR VEHICLE

«
...
320
321
322
323
324
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: EAL Pages: 4

Brand: Jeep Pages: 608

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Actia Pages: 102

Brand: Magneti Marelli Pages: 2

Brand: Audi Pages: 63

Brand: Thule Pages: 2

Brand: Aston Martin Pages: 415

Brand: Ford Pages: 8

Brand: Saab Pages: 9

80-485-142401-RT

Brand: Classic Accessories Pages: 14

Brand: Prorack Pages: 15

ASENTO EV-EXP18R

Brand: ADAPT SOLUTIONS Pages: 25

Brand: Vauxhall Pages: 310

Brand: Whispbar Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands