Dodge 2014 Ram 1500 Owner'S Manual Download Page 37 | Manualshive

Page: 37 / 360

background image

5. EVIC Amber Telltales

•

Low Fuel Telltale

When the fuel level reaches approximately 3.0 gal
(11.0 L) this light will turn on, and remain on until
fuel is added.

•

Windshield Washer Fluid Low Indicator

This telltale will turn on to indicate the wind-
shield washer fluid is low.

•

Low Coolant Level Indicator

This telltale will turn on to indicate the vehicle
coolant level is low.

•

Transmission Temperature Warning Telltale

This telltale indicates that the transmission
fluid temperature is running hot. This may
occur with severe usage, such as trailer towing.

If this telltale turns on, safely pull over and stop the
vehicle. Then, shift the transmission into NEUTRAL and
run the engine at idle or faster until the light turns off.

CAUTION!

Continuous driving with the Transmission Tempera-
ture Warning Light illuminated will eventually cause
severe transmission damage or transmission failure.

WARNING!

If you continue operating the vehicle when the
Transmission Temperature Warning Light is illumi-
nated you could cause the fluid to boil over, come in
contact with hot engine or exhaust components and
cause a fire.

3

UNDERSTANDING YOUR INSTRUMENT PANEL

35

«
...
35
36
37
38
39
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Ignition Pages: 1

Brand: Vaisala Pages: 24

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Brand: GOgroove Pages: 9

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

Brand: Cadillac Pages: 407

Brand: Mercedes-Benz Pages: 358

Brand: ULTIMATE SPEED Pages: 50

Brand: AEM Pages: 27

Brand: JKS Pages: 6

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Elinchrom Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands