Dodge 2014 Ram 1500 Owner'S Manual Download Page 112 | Manualshive

Page: 112 / 360

background image

CAUTION!

The starter motor will engage for approximately 30
seconds at a time. Allow two minutes between crank-
ing intervals.

NOTE:

The engine may run rough until the air is forced

from all the fuel lines.

WARNING!

Do not use alcohol or gasoline as a fuel blending
agent. They can be unstable under certain conditions
and be hazardous or explosive when mixed with
diesel fuel.

CAUTION!

Due to lack of lubricants in alcohol or gasoline, the
use of these fuels can cause damage to the fuel
system.

NOTE:

•

We recommend you use a blend of up to 5% biodiesel,
that meets ASTM specification D-975 with your diesel
engine. Use of biodiesel mixture in excess of 20% can
negatively impact the fuel filter’s ability to separate
water from the fuel, resulting in high pressure fuel
system corrosion or damage.

•

In addition, commercially available fuel additives are
not necessary for the proper operation of your diesel
engine.

110

MAINTAINING YOUR VEHICLE

«
...
110
111
112
113
114
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Daihatsu Pages: 43

2012 Escalade Hybrid

Brand: Cadillac Pages: 90

Brand: FormFit Pages: 2

Brand: AutoWatch Pages: 4

Brand: Hyundai Pages: 19

Brand: POOL-LINE Pages: 2

Brand: Jaeger Pages: 14

Brand: Renault Pages: 3699

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

Brand: Volvo Pages: 7

Brand: Subaru Pages: 786

Brand: Genesis Pages: 690

Brand: Air Lift Pages: 24

Brand: Buzz Rack Pages: 8

Brand: PAC Pages: 4

Brand: Prorack Pages: 14

Brand: WALMEC Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands