Dodge 2014 Ram 1500 Owner'S Manual Download Page 298 | Manualshive

Page: 298 / 360

background image

Disposing Of Used Engine Oil And Oil Filters

Care should be taken in disposing of used engine oil and
oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to the
environment. Contact your authorized dealer, service
station or governmental agency for advice on how and
where used oil and oil filters can be safely discarded in
your area.

Engine Air Cleaner Filter

CAUTION!

All air entering the engine intake must be filtered.
The abrasive particles in unfiltered air will cause
rapid wear to engine components.

WARNING!

The air induction system (air cleaner, hoses, etc.)
provides a measure of protection. Do not remove the
air induction system (air cleaner, hoses, etc.) unless
such removal is necessary for repair or maintenance.
Make sure that no one is near the engine compart-
ment before starting the vehicle with the air induc-
tion system (air cleaner, hoses, etc.) removed. Failure
to do so can result in serious personal injury.

The condition of the air cleaner filter is monitored by the
Engine Control Module. The “SERVICE AIR FILTER” mes-
sage will display in the Electronic Vehicle Information
Center (EVIC) when service is required. Refer to “Elec-
tronic Vehicle Information Center (EVIC)” in “Understand-
ing Your Instrument Panel” for further information.

296

MAINTAINING YOUR VEHICLE

«
...
296
297
298
299
300
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: ZAPTEC Pages: 240

Brand: A-Tach Mounts Pages: 2

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

iBoard IB-ZK406

Brand: APS Auto Parts Specialist Pages: 3

Brand: PullRite Pages: 10

Brand: Mercedes-Benz Pages: 54

Brand: Xblitz Pages: 30

Brand: Buick Pages: 20

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: r.LiNK Pages: 20

Brand: Curt Group Pages: 2

Brand: Volkswagen Zubehör Pages: 40

Brand: Volkswagen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands