Dodge 2014 Ram 1500 Owner'S Manual Download | Manualshive

Page: 266 / 360

background image

Weight-Distributing Hitch

A weight-distributing system works by applying lever-
age through spring (load) bars. They are typically used
for heavier loads to distribute trailer tongue weight to the
tow vehicle’s front axle and the trailer axle(s). When used
in accordance with the manufacturer’s directions, it pro-
vides for a more level ride, offering more consistent
steering and brake control thereby enhancing towing
safety. The addition of a friction/hydraulic sway control
also dampens sway caused by traffic and crosswinds and
contributes positively to tow vehicle and trailer stability.
Trailer sway control and a weight distributing (load
equalizing) hitch are recommended for heavier Tongue
Weights (TW) and may be required depending on vehicle
and trailer configuration/loading to comply with Gross
Axle Weight Rating (GAWR) requirements.

WARNING!

•

An improperly adjusted Weight Distributing Hitch
system may reduce handling, stability, braking
performance, and could result in a collision.

•

Weight Distributing Systems may not be compat-
ible with Surge Brake Couplers. Consult with your
hitch and trailer manufacturer or a reputable Rec-
reational Vehicle dealer for additional information.

Fifth-Wheel Hitch

The fifth-wheel hitch is a special high platform with a
coupling that mounts over the rear axle of the tow vehicle
in the truck bed. It connects a vehicle and fifth-wheel
trailer with a coupling king pin.

264

STARTING AND OPERATING

«
...
264
265
266
267
268
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: cam Pages: 28

Brand: Wallbox Pages: 7

Brand: Honda Pages: 85

Q Access Alpha GSE 2023

Brand: Q Mobility Group Pages: 9

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: Mercedes-Benz Pages: 91

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: r.LiNK Pages: 20

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

Brand: Buick Pages: 371

Brand: Brodit Pages: 2

Brand: Poison Spyder Pages: 5

Brand: Ford Pages: 8

Brand: Hyundai Pages: 32

DODGE AD100 1993

Brand: Chrysler Pages: 1502

V2 Two-Bike Carrier

Brand: LetsGoAero Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands