Dodge 2014 Ram 1500 Owner'S Manual Download Page 323 | Manualshive

Page: 323 / 360

background image

NOTE:

If it is necessary to check the transmission

below

the operating temperature, the fluid level should be
between the two “COLD” (lower) holes on the dipstick
with the fluid at 60-70°F / 16-21°C for 68RFE transmis-
sion, or 68-86°F / 20-30°C for AS69RC transmission. Only
use the COLD region of the dipstick as a rough reference
when setting the fluid level after a transmission service
or fluid change. Re-check the fluid level, and adjust as
required, once the transmission reaches normal operating
temperature.

CAUTION!

If the fluid temperature is below 50°F (10°C) it may
not register on the dipstick. Do not add fluid until
the temperature is elevated enough to produce an
accurate reading. Run the engine at idle, in PARK, to
warm the fluid.

8. Check for leaks. Release the parking brake.

NOTE:

To prevent dirt and water from entering the

transmission after checking or replenishing fluid, make
sure that the dipstick cap is properly reseated. It is
normal for the dipstick cap to spring back slightly from
its fully seated position, as long as its seal remains
engaged in the dipstick tube.

Fluid And Filter Changes

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

In addition, change the fluid and filter(s) if the fluid
becomes contaminated (with water, etc.), or if the trans-
mission is disassembled for any reason.

6

MAINTAINING YOUR VEHICLE

321

«
...
321
322
323
324
325
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Davis Instruments Pages: 16

Brand: Jeep Pages: 212

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Kolpin Pages: 25

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: Gator Pages: 2

Brand: Porsche Pages: 313

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

Brand: MULTILIFT Pages: 62

Brand: Motoalliance Pages: 5

Brand: Streetwize Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands