Dodge 2014 Ram 1500 Owner'S Manual Download Page 220 | Manualshive

Page: 220 / 360

background image

NOTE:

For EVIC messages related to the vehicle’s ex-

haust system, refer to “Maintenance Procedures/
Intervention Regeneration Strategy – EVIC Message Pro-
cess Flow” in “Maintaining Your Vehicle” for further
information.

Idle-Up Feature — Automatic Transmission Only

The driver-controlled high idle speed feature will help
increase cylinder temperatures and provide additional
cab heat, however, excessive idling may still cause the
exhaust aftertreatment system to not properly regenerate.
Extended periods of idle time should be avoided.

The Idle-Up feature uses the speed control switches to
increase engine idle speed and quickly warm the vehi-
cle’s interior.

1. With the transmission in PARK, the parking brake

applied, and the engine running, press the speed
control switch to the ON position, then press the SET
switch.

2. The engine RPM will go up to 1100 RPM. To increase

the RPM, press and hold the ACCEL/RESUME switch
and the idle speed will increase to approximately 1500
RPM. To decrease the RPM, press and hold the DECEL
switch and the idle speed will decrease to approxi-
mately 1100 RPM.

3. To cancel the Idle–Up feature, either press the CAN-

CEL switch, press the ON/OFF switch, or press the
brake pedal.

Stopping The Engine

Idle the engine a few minutes before routine shutdown.
After full load operation, idle the engine three to five
minutes before shutting it down. This idle period will

218

STARTING AND OPERATING

«
...
218
219
220
221
222
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: GMC Pages: 140

Brand: Front Runner Pages: 5

Brand: Chariot Carriers Pages: 3

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: EZTRUNK Pages: 3

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Camoplast Pages: 19

Brand: E&G Classics Pages: 4

Brand: v.link Pages: 12

Brand: iDataLink Pages: 6

Brand: ULTIMATE SPEED Pages: 56

Brand: Volvo Pages: 18

Brand: Westin Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands