Dodge 2014 Ram 1500 Owner'S Manual Download Page 200

Page: 200 / 360

Vehicles Not Equipped With Passive Entry

1. Without pressing the brake pedal, cycle the ignition to

the ON/RUN position (do not start the engine.)

2. Press and release the

DOWN

arrow button to scroll

downward through the main menu to “

Vehicle Info

”.

3. Press and release the

RIGHT

arrow button to access

the ”

Oil Life

” screen.

4. Press and hold the

RIGHT

arrow button for one

second to access the ”

Oil Life Reset

” screen.

5. Press and release the

DOWN

arrow button to select

“Yes”, then press and release the Right arrow button to
select reset of the Oil Life.

6. Press and release the

arrow button to exit the EVIC

screen.

NOTE:

If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.

198

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands

Dodge 2014 Ram 1500, Owner'S Manual

Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands