Dodge 2014 Ram 1500 Owner'S Manual Download Page 173 | Manualshive

Page: 173 / 360

background image

4. EVIC White Telltales

•

Electronic Speed Control Ready

This light will turn on when the electronic
speed control is ON. For further information,
refer to “Electronic Speed Control” in “Under-
standing The Features Of Your Vehicle.”

•

Electronic Speed Control SET

This light will turn on when the electronic
speed control is SET. For further information,
refer to “Electronic Speed Control” in “Under-
standing The Features Of Your Vehicle.”

•

Shift Lever Status

The highest available transmission gear is displayed in
the lower right corner of the Electronic Vehicle Informa-
tion Center (EVIC) whenever the Electronic Range Select
(ERS) feature is active. Use the +/- selector on the shift
lever to activate ERS. Refer to “Automatic Transmission”
in “Starting And Operating” for further information.

5. EVIC Amber Telltales

•

Low Fuel Telltale

When the fuel level reaches approximately 3.0 gal
(11.0 L) this light will turn on, and remain on until
fuel is added.

•

Windshield Washer Fluid Low Indicator

This telltale will turn on to indicate the wind-
shield washer fluid is low.

•

Low Coolant Level Indicator

This telltale will turn on to indicate the vehicle
coolant level is low.

•

Transmission Temperature Warning Telltale

This telltale indicates that the transmission
fluid temperature is running hot. This may
occur with severe usage, such as trailer towing.

3

UNDERSTANDING YOUR INSTRUMENT PANEL

171

«
...
171
172
173
174
175
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

Brand: Metra Electronics Pages: 2

Intercooler Kit Type 31

Brand: GReddy Pages: 9

Brand: Honda Pages: 32

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: BrandMotion Pages: 2

Brand: Ford Pages: 52

Brand: Dakota Digital Pages: 20

Giulietta 2.0 JTDM

Brand: Alfa Romeo Pages: 14

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

2013 Zafira Tourer

Brand: Vauxhall Pages: 289

Brand: HUSKY LINERS Pages: 4

Brand: iOttie Pages: 19

KY-700-2018-DRW01

Brand: FALCON RIDGE Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands