Dodge 2014 Ram 1500 Owner'S Manual Download Page 188

Page: 188 / 360

NOTE:

If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.

Electronic Vehicle Information Center (EVIC)
Displays — 7” Display

The EVIC displays are located in the center portion of the
cluster and consists of eight sections:

1. Main Screen — The inner ring of the display will

illuminate in grey under normal conditions, yellow for
non critical warnings, red for critical warnings and
white for on demand information.

2. Audio/Phone Information and Sub-menu Information

— Whenever there are sub-menus available, the posi-
tion within the sub-menus is shown here.

3. Selectable Information (Compass, Temp, Range to

Empty, Trip A, Trip B, Average MPG, Trailer Trip
(distance only), Trailer Brake Gain).

4. Telltales/Indicators

5. Shift Lever Status (PRNDL)

6. Selectable Menu Icons

7. Air Suspension Status – If Equipped

8. 4WD Status

186

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands

Dodge 2014 Ram 1500, Owner'S Manual

Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands