Dodge 2014 Ram 1500 Owner'S Manual Download Page 131

Page: 131 / 360

Required Maintenance

Refer to the Maintenance Schedules on the following
pages for required maintenance.

At Every Oil Change Interval As Indicated By Oil

Change Indicator System:

•

Change oil and filter.

•

Completely fill the Diesel Exhaust Fluid tank.

•

Drain water from fuel filter assembly.

•

Rotate the tires.

Rotate at the first sign of irregu-

lar wear, even if it occurs before the oil indicator
system turns on.

•

Inspect battery and clean and tighten terminals as
required.

•

Inspect automatic transmission fluid if equipped
with dipstick.

At Every Oil Change Interval As Indicated By Oil

Change Indicator System:

•

Inspect brake pads, shoes, rotors, drums, hoses
and park brake.

•

Inspect engine cooling system protection and
hoses.

•

Inspect exhaust system.

•

Inspect engine air cleaner if using in dusty or
off-road conditions.

MAINTENANCE SCHEDULE

129

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands

Dodge 2014 Ram 1500, Owner'S Manual

Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands