Dodge 2014 Ram 1500 Owner'S Manual Download Page 74 | Manualshive

Page: 74 / 360

background image

CAUTION!

Use of blends greater than 20% is not approved. Use
of blends greater than 20% can result in engine
damage. Such damage is not covered by the New
Vehicle Limited Warranty.

Biodiesel Fuel Properties — Low Ambient
Temperatures

Biodiesel fuel may gel or solidify at low ambient tem-
peratures, which may pose problems for both storage and
operation. Precautions can be necessary at low ambient
temperatures, such as storing the fuel in a heated build-
ing or a heated storage tank, or using cold temperature
additives.

Fuel Quality — Must Comply With ASTM
Standards

The quality of Biodiesel fuel may vary widely. Only fuel
produced by a BQ9000 supplier to the following specifi-
cations may be blended to meet Biodiesel blend B6 – B20
fuel meeting ASTM specification D-7467:

•

Petrodiesel fuel meeting ASTM specification D-975
and Biodiesel fuel (B100) meeting ASTM specification
D-6751

Fuel Oxidation Stability — Must Use Fuel Within
Six Months Of Manufacture

Biodiesel fuel has poor oxidation stability which can
result in long term storage problems. Fuel produced to
approved ASTM standards, if stored properly, provides
for protection against fuel oxidation for up to six months.

72

STARTING AND OPERATING

«
...
72
73
74
75
76
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Accel Pages: 2

Brand: Whispbar Pages: 17

Sedan CIVIC 2022

Brand: Honda Pages: 701

2013 GMC Savana

Brand: GMC Pages: 398

2010 MX-5 Miata

Brand: Mazda Pages: 8

RAV-4 2015 Series

Brand: Toyota Pages: 50

Brand: Saab Pages: 37

Brand: Fabbri Pages: 32

Brand: Whelen Engineering Company Pages: 2

Brand: PEUGEOT Pages: 232

Brand: Aries Pages: 3

Brand: Guardsman Pages: 2

Brand: Curt Group Pages: 2

Brand: Easee Pages: 21

Bounder turbo diesel 2001

Brand: Fleetwood Pages: 166

Brand: Toyota Pages: 204

Brand: Buick Pages: 20

Brand: Valeo Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands