Dodge 2014 Ram 1500 Owner'S Manual Download Page 268 | Manualshive

Page: 268 / 360

background image

Trailer Towing Weights (Maximum Trailer Weight
Ratings)

NOTE:

For additional trailer towing information (maxi-

mum trailer weight ratings) refer to the following website
addresses:

•

ramtrucks.com/en/towing_guide/

•

ramtruck.ca (Canada)

•

rambodybuilder.com

Trailer And Tongue Weight

Always load a trailer with 60% of the weight in the front
of the trailer. This places 10% of the GTW on the tow
hitch of your vehicle. Loads balanced over the wheels or
heavier in the rear can cause the trailer to sway

severely

side to side which will cause loss of control of the vehicle
and trailer. Failure to load trailers heavier in front is the
cause of many trailer collisions. Never exceed the maxi-
mum tongue weight stamped on your trailer hitch.

Consider the following items when computing the
weight on the rear axle of the vehicle:

•

The tongue weight of the trailer

•

The weight of any other type of cargo or equipment
put in or on your vehicle

•

The weight of the driver and all passengers

266

STARTING AND OPERATING

«
...
266
267
268
269
270
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Vauxhall Pages: 2

Brand: UMBRA RIMORCHI Pages: 18

Brand: Ford Pages: 12

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Honda Pages: 32

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Brand: AA Products Pages: 4

Brand: Menabo Pages: 12

Brand: Ecco Pages: 9

Brand: Jaeger Pages: 13

Brand: Elinchrom Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands