Dodge 2014 Ram 1500 Owner'S Manual Download Page 76 | Manualshive

Page: 76 / 360

background image

TRAILER TOWING

In this section you will find safety tips and information
on limits to the type of towing you can reasonably do
with your vehicle. Before towing a trailer, carefully
review this information to tow your load as efficiently
and safely as possible.

To maintain the New Vehicle Limited Warranty coverage,
follow the requirements and recommendations in this
manual concerning vehicles used for trailer towing.

Common Towing Definitions

The following trailer towing related definitions will assist
you in understanding the following information:

Gross Vehicle Weight Rating (GVWR)

The GVWR is the total allowable weight of your vehicle.
This includes driver, passengers, cargo and tongue
weight. The total load must be limited so that you do not

exceed the GVWR. Refer to “Vehicle Loading/Vehicle
Certification Label” in “Starting and Operating” for
further information.

Gross Trailer Weight (GTW)

The GTW is the weight of the trailer plus the weight of all
cargo, consumables and equipment (permanent or tem-
porary) loaded in or on the trailer in its

⬙

loaded and

ready for operation

⬙

condition. The recommended way to

measure GTW is to put your fully loaded trailer on a
vehicle scale. The entire weight of the trailer must be
supported by the scale.

Gross Combination Weight Rating (GCWR)

The GCWR is the total permissible weight of your vehicle
and trailer when weighed in combination.

74

STARTING AND OPERATING

«
...
74
75
76
77
78
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Lancia Pages: 191

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: CITROEN Pages: 52

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

Brand: Phonocar Pages: 6

Brand: Actia Pages: 37

Brand: BMW Pages: 21

Brand: GMC Pages: 20

Brand: Kuda Pages: 2

Brand: Prorack Pages: 15

Brand: Mercedes-Benz Pages: 398

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: ZENEC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands