Dodge 2014 Ram 1500 Owner'S Manual Download Page 336 | Manualshive

Page: 336 / 360

background image

MAINTENANCE SCHEDULE — DIESEL ENGINE

CAUTION!

Failure to perform the required maintenance items
may result in damage to the vehicle.

At Each Stop For Fuel

Check the engine oil level at least 30 minutes after a fully
warmed engine is shut off. Checking the oil level while
the vehicle is on level ground will improve the accuracy
of the oil level reading. Add oil only when the level is at
or below the ADD or MIN mark.

Once A Month

•

Inspect the batteries, and clean and tighten the termi-
nals as required.

•

Check the fluid levels of the coolant reservoir, brake
master cylinder, and automatic transmission (if
equipped), and add as needed.

At Each Oil Change

•

Change the engine oil filter.

•

Inspect the exhaust system.

•

Inspect engine air filter.

•

Check the coolant level, hoses, and clamps.

•

Lubricate outer tie rod ends.

Inspection and service should also be performed anytime
a malfunction is observed or suspected. Retain all re-
ceipts.

334

MAINTENANCE SCHEDULE

«
...
334
335
336
337
338
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Daihatsu Pages: 43

Brand: Jeep Pages: 25

Brand: HALE Pages: 44

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Brand: EEZ RV Pages: 31

Brand: Wilco Offroad Pages: 4

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Actia Pages: 102

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: Renault Pages: 340

Brand: A-Tach Pages: 2

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Power Acoustik Pages: 4

Brand: Yakima Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands