Dodge 2014 Ram 1500 Owner'S Manual Download Page 219 | Manualshive

Page: 219 / 360

background image

Your vehicle is equipped with a turbo speed limiter, this
feature limits the engine speed to 1,200 RPM when
engine coolant temperatures are below 70°F (21°C). This
feature is designed to protect the turbocharger from
damage and will only operate in PARK or NEUTRAL.

If temperatures are below 32°F (0°C), operate the engine
at moderate speeds for five minutes before full loads are
applied.

NOTE:

If ambient temperatures are low and the coolant

temperature is below 180°F (82°C), the engine idle speed
will slowly increase to 1,000 RPM after two minutes of
idle, if the following conditions are met:

•

Foot is off brake pedal and throttle pedal.

•

Automatic transmission is in PARK.

•

Vehicle speed is 0 mph (0 km/h).

•

Applying the throttle will cancel fast idle.

•

Operating the exhaust brake at idle will greatly im-
prove warm up rate and will help keep the engine
close to operating temperature during extended idle.

Engine Idling

Avoid prolonged idling, long periods of idling may be
harmful to your engine because combustion chamber
temperatures can drop so low that the fuel may not burn
completely. Incomplete combustion allows carbon and
varnish to form on piston rings, engine valves, and
injector nozzles. Also, the unburned fuel can enter the
crankcase, diluting the oil and causing rapid wear to the
engine.

If the engine is allowed to idle, under some conditions
the idle speed may increase to 900 RPM then return to
normal idle speed. This is normal operation.

4

STARTING AND OPERATING

217

«
...
217
218
219
220
221
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Daihatsu Pages: 1718

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: GMC Pages: 20

Brand: Rati Pages: 2

Brand: Volvo Pages: 24

Brand: Fab Fours Pages: 13

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Brand: Bestop Pages: 31

Brand: Subaru Pages: 44

Brand: Oldsmobile Pages: 358

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands