Dodge 2014 Ram 1500 Owner'S Manual Download Page 274 | Manualshive

Page: 274 / 360

background image

sliding the manual brake control lever will display the
GAIN setting for 10 seconds and the “Trailer Brake Status
Indicator Light” will not be displayed.

If a fault is detected in the trailer wiring or the Integrated
Trailer Brake Module (ITBM), the “Trailer Brake Status
Indicator Light” will flash.

GAIN Adjustment Buttons (+/-)

Pressing these buttons will adjust the brake control
power output to the trailer brakes in 0.5 increments. The
GAIN setting can be increased to a maximum of 10 or
decreased to a minimum of 0 (no trailer braking).

GAIN

The GAIN setting is used to set the trailer brake control
for the specific towing condition and should be changed
as towing conditions change. Changes to towing condi-
tions include trailer load, vehicle load, road conditions
and weather.

Adjusting GAIN

NOTE:

This should only be performed in a traffic free

environment at speeds of approximately 20–25 mph
(30–40 km/h).

1. Make sure the trailer brakes are in good working

condition, functioning normally and properly ad-
justed. See your trailer dealer if necessary.

2. Hook up the trailer and make the electrical connections

according to the trailer manufacturer’s instructions.

3. When a trailer with electric/EOH brakes is plugged

in, the trailer connected message should appear in the
EVIC (if the connection is not recognized by the ITBM,
braking functions will not be available), the GAIN
setting will illuminate and the correct type of trailer
must be selected from the EVIC options.

4. Press the UP or DOWN button on the steering wheel

until “TRAILER TOW” appears on the screen.

272

STARTING AND OPERATING

«
...
272
273
274
275
276
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Wagan Pages: 12

Brand: Jeep Pages: 608

Brand: Globalsat Pages: 2

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Toro Pages: 24

Brand: NanoCam Plus Pages: 32

Brand: Mercedes-Benz Pages: 398

Brand: Thule Pages: 8

Brand: Arrista Pages: 2

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

2010 Accord Coupe

Brand: Honda Pages: 410

Brand: DICE Pages: 1

Brand: Hudson Pages: 24

Brand: Quadratec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands