Dodge 2014 Ram 1500 Owner'S Manual Download Page 307 | Manualshive

Page: 307 / 360

background image

CAUTION!

•

Diesel fuel will damage blacktop paving surfaces.
Drain the filter into an appropriate container.

•

Do not prefill the fuel filter when installing a new
fuel filter. There is a possibility debris could be
introduced into the fuel filter during this action. It
is best to install the filter dry and allow the in-tank
lift pump to prime the fuel system.

1. Ensure engine is turned off.

2. Place drain pan under the fuel filter drain hose.

3. Open the water drain valve 1 full turn counterclock-

wise and completely drain fuel and water into the
approved container.

4. Close the water drain valve.

5. Remove lid using a socket or strap wrench. Rotate

counterclockwise for removal. Remove used o-ring
and discard it.

6. Remove the used filter cartridge from the housing and

dispose of according to your local regulations.

7. Wipe clean the sealing surfaces of the lid and housing.

8. Install new o-ring back into ring groove on the filter

housing and lubricate with clean engine oil.

NOTE:

WIF sensor is re-usable. Service kit comes with

new o-ring for filter canister and WIF sensor.

6

MAINTAINING YOUR VEHICLE

305

«
...
305
306
307
308
309
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Calix Pages: 5

Brand: Hella Pages: 21

Brand: Pyle Pages: 2

Brand: Cadillac Pages: 20

Brand: Mont Blanc Pages: 2

Brand: Ford Pages: 40

Brand: Ford Pages: 2

Brand: ULTIMATE SPEED Pages: 56

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Civic Hatch 2017

Brand: Honda Pages: 687

Brand: Edelbrock Pages: 2

Brand: JBA Pages: 5

Brand: Hyundai Pages: 32

Brand: NavLinkz Pages: 24

Brand: iSimple Pages: 16

Brand: LAS Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands