Dodge 2014 Ram 1500 Owner'S Manual Download Page 258 | Manualshive

Page: 258 / 360

background image

ADDING FUEL — CHASSIS CAB MODELS

CAUTION!

To avoid fuel spillage and overfilling, do not “top
off” the fuel tank after filling.

NOTE:

•

When the fuel nozzle “clicks” or shuts off, the fuel tank
is full.

•

Tighten the fuel filler cap until you hear a “clicking”
sound. This is an indication that the fuel filler cap is
properly tightened.

•

Make sure that the fuel filler cap is tightened each time
the vehicle is refueled.

WARNING!

A fire may result if fuel is pumped into a portable
container that is on a truck bed. You could be burned.
Always place fuel containers on the ground while
filling.

Fuel Filler Cap

If the fuel filler cap is lost or damaged, be sure the
replacement cap is for use with this vehicle.

CAUTION!

Damage to the fuel system or emission control sys-
tem could result from using an improper fuel tank
filler tube cap. A poorly fitting cap could let impuri-
ties into the fuel system.

256

STARTING AND OPERATING

«
...
256
257
258
259
260
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Daihatsu Pages: 485

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: Tessera4x4 Pages: 20

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: MAXWORKS Pages: 7

Brand: M7 SPEED Pages: 6

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Brand: Radical Sportscars Pages: 44

Brand: Prorack Pages: 10

Brand: Power Acoustik Pages: 4

Brand: Discount Car Stereo Pages: 8

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: Volvo Pages: 362

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands