Dodge 2014 Ram 1500 Owner'S Manual Download Page 115 | Manualshive

Page: 115 / 360

background image

spraying water from a garden hose vertically down the
face of the A/C condenser (if equipped) or the back of the
radiator core.

Check the engine cooling system hoses for brittle rubber,
cracking, tears, cuts and tightness of the connection at the
coolant recovery bottle and radiator. Inspect the entire
system for leaks.

With the engine at normal operating temperature (but
not running), check the cooling system pressure cap for
proper vacuum sealing by draining a small amount of
engine coolant (antifreeze) from the radiator drain cock.
The radiator drain cock is located in the lower radiator
tank. If the cap is sealing properly, the engine coolant
(antifreeze) will begin to drain from the coolant expan-
sion bottle. DO NOT REMOVE THE COOLANT PRES-
SURE CAP WHEN THE COOLING SYSTEM IS HOT.

Cooling System — Drain Flush And Refill

If the engine coolant (antifreeze) is dirty or contains a
considerable amount of sediment, clean and flush with a
reliable cooling system cleaner. Follow with a thorough
rinsing to remove all deposits and chemicals. Properly
dispose of old engine coolant (antifreeze).

Refer to the “Maintenance Schedule” for the proper
maintenance intervals.

Selection Of Coolant

Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for further information.

5

MAINTAINING YOUR VEHICLE

113

«
...
113
114
115
116
117
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Daihatsu Pages: 43

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: Toyota Pages: 35

Brand: EUFAB Pages: 12

Brand: Axxess Pages: 8

Brand: Quadratec Pages: 12

Akerstroms Tx700

Brand: LXE Pages: 146

Brand: A-Tach Mounts Pages: 2

Brand: Renault Pages: 198

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

Brand: Jaeger Pages: 16

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Ranger design Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands