Dodge 2014 Ram 1500 Owner'S Manual Download Page 210 | Manualshive

Page: 210 / 360

background image

•

A 12 Volt heater built into the fuel filter housings aid in
preventing fuel gelling. It is controlled by a built-in
thermostat.

•

A heated intake air system both improves engine
starting and reduces the amount of white smoke
generated by a warming engine.

Normal Starting Procedure — Engine Manifold Air
Temperature Above 66° F (19° C)

Observe the instrument panel cluster lights when starting
the engine.

1. Always apply the parking brake.

2. Shift into PARK for an automatic transmission. For

vehicles equipped with a manual transmission, fully
press and hold the clutch pedal and shift into NEU-
TRAL.

3. Turn the ignition switch to the ON position and watch

the instrument panel cluster lights.

CAUTION!

If the “Water in Fuel Indicator Light” remains on, DO
NOT START the engine before you drain the water
from the fuel filters to avoid engine damage. Refer to
“Maintenance Procedures/Draining Fuel/Water Sepa-
rator Filter” in “Maintaining Your Vehicle” for fur-
ther information.

4. Turn the ignition switch to the START position and

crank the engine. Do not press the accelerator during
starting.

208

STARTING AND OPERATING

«
...
208
209
210
211
212
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Camcar Pages: 6

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: 3SIXT Pages: 12

Brand: GATmatic Pages: 13

Brand: Porsche Pages: 195

Brand: Whispbar Pages: 15

Brand: Icom Pages: 20

Brand: U.S. General Pages: 8

Brand: TrailFX Pages: 2

Brand: Jeep Pages: 374

Brand: ACV Pages: 2

Brand: Metra Electronics Pages: 10

Brand: Beeper Pages: 2

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brand: Saab Pages: 498

Brand: Laser Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands