Dodge 2014 Ram 1500 Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 360

background image

Gross Axle Weight Rating (GAWR)

The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
evenly. Make sure that you do not exceed either front or
rear GAWR. Refer to “Vehicle Loading/Vehicle Certifica-
tion Label” in “Starting and Operating” for further
information.

WARNING!

It is important that you do not exceed the maximum
front or rear GAWR. A dangerous driving condition
can result if either rating is exceeded. You could lose
control of the vehicle and have an accident.

Tongue Weight (TW)

The tongue weight is the downward force exerted on the
hitch ball by the trailer. In most cases it should not be less
than 10% of the trailer load. You must consider this as
part of the load on your vehicle.

Frontal Area

The frontal area is the maximum height multiplied by the
maximum width of the front of a trailer.

Trailer Sway Control

The trailer sway control can be a mechanical telescoping
link that can be installed between the hitch receiver and
the trailer tongue that typically provides adjustable fric-
tion associated with the telescoping motion to dampen
any unwanted trailer swaying motions while traveling.

4

STARTING AND OPERATING

75

«
...
75
76
77
78
79
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Camcar Pages: 6

Brand: Acdeos Pages: 7

Brand: Jabra Pages: 10

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: M7 SPEED Pages: 6

Brand: travall Pages: 4

Brand: TATA Motors Pages: 166

Brand: Advanced Diagnostics Pages: 10

Brand: AutoLoc Pages: 6

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Edelbrock Pages: 2

Brand: Saab Pages: 37

Brand: Motoalliance Pages: 4

Brand: Kargo Master Pages: 9

Heavy Duty ProClip

Brand: Brodit Pages: 2

Brand: Kargo Master Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands