Dodge 2014 Ram 1500 Owner'S Manual Download Page 239 | Manualshive

Page: 239 / 360

background image

CAUTION!

When using ERS for engine braking while descend-
ing steep grades, be careful not to overspeed the
engine. Apply the brakes as needed to prevent en-
gine overspeed.

Overdrive Operation

The automatic transmission includes an electronically
controlled Overdrive (fifth and sixth gears). The trans-
mission will automatically shift into Overdrive if the
following conditions are present:

•

The shift lever is in the DRIVE position.

•

The transmission fluid has reached an adequate tem-
perature.

•

The engine coolant has reached an adequate tempera-
ture.

•

The vehicle speed is sufficiently high.

•

The driver is not heavily pressing the accelerator.

When To Use TOW/HAUL Mode

When driving in hilly areas, towing a trailer, carrying a
heavy load, etc., and frequent transmission shifting oc-
curs, press the TOW/HAUL switch to activate TOW/
HAUL mode. This will improve performance and reduce
the potential for transmission overheating or failure due
to excessive shifting. When operating in TOW/HAUL
mode, transmission upshifts are delayed, and the trans-
mission will automatically downshift (for engine brak-
ing) when the throttle is closed and/or during steady
braking maneuvers.

4

STARTING AND OPERATING

237

«
...
237
238
239
240
241
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Eclipse Pages: 6

Brand: Quadratec Pages: 8

Brand: GOgroove Pages: 9

Brand: TrailFX Pages: 6

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: Compass Pages: 16

Brand: Cadillac Pages: 518

Brand: Opel Pages: 141

Brand: Yakima Pages: 21

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: Dacia Pages: 238

Brand: PEUGEOT Pages: 249

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands