Dodge 2014 Ram 1500 Owner'S Manual Download | Manualshive

Page: 67 / 360

background image

•

Climatized Ultra Low Sulfur Diesel Fuel is a blend of
Number 2 Ultra Low Sulfur and Number 1 Ultra Low
Sulfur Diesel Fuels which reduces the temperature at
which wax crystals form in fuel.

•

The fuel grade should be clearly marked on the pump
at the fuel station.

•

The engine requires the use of

“Ultra Low Sulfur

Diesel Fuel”

. Use of incorrect fuel could result in

engine and exhaust system damage. Refer to “Fuel
Requirements” in “Starting And Operating” for fur-
ther information.

Engine Oil Usage

Refer to “Maintenance Procedures” in “Maintaining Your
Vehicle” for the correct engine oil viscosity.

Engine Warm-Up

Avoid full throttle operation when the engine is cold.
When starting a cold engine, bring the engine up to
operating speed slowly to allow the oil pressure to
stabilize as the engine warms up.

If temperatures are below 32°F (0°C), operate the engine
at moderate speeds for five minutes before full loads are
applied.

Engine Idling

Avoid prolonged idling, long periods of idling may be
harmful to your engine because combustion chamber
temperatures can drop so low that the fuel may not burn
completely. Incomplete combustion allows carbon and
varnish to form on piston rings, cylinder head valves,
and injector nozzles. Also, the unburned fuel can enter
the crankcase, diluting the oil and causing rapid wear to
the engine.

4

STARTING AND OPERATING

65

«
...
65
66
67
68
69
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Abarth Pages: 176

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

Brand: Saab Pages: 3

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

S90 - ACCESSORY PANEL

Brand: Volvo Pages: 166

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Flash Cover Pages: 2

Brand: Subaru Pages: 399

Brand: Carbest Pages: 64

Brand: Honda Pages: 2

Brand: Car-Interface Pages: 25

Brand: Beeper Pages: 2

Brand: Yakima Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands