185 Bosstick boulevard
san Marcos, ca 92069
phone 760-560-2252
fax 760-560-0383
www.bajadesigns.com
2019 RAM
Select Models
Fog pocket installation
3
4
5
5
4
8mm
DRIVER SIDE
1
2
1
2
3
8mm
Remove the five (5), 8mm inner fender liner screws as shown and remove the
lower portion of the wheel well. Screws located in positions and must be
used in this location when reassembling.
1.
4
5
2.
Use a 10mm wrench to remove the
indicated nut in region . Use a 10mm
socket and ratchet to remove the
indicated screw in region . Unplug the
fog light.
7
8
Please be patient as this is a tedious step.
Use a
T27 Torx
or
5mm Hex
bit in a
1/4”
short socket & short ratchet to remove the
top 2 screws indicated in region . Hand
space will be limited.
3.
6
TOP OF BUMPER
BEHIND BUMPER VIEW DS
7
8
10mm
6
7
8
10mm
Side View
9.8
Top View
6
T27
5mm Hex
Use a 7mm socket with an extension to remove the OEM fog
light from the plastic bracket. Hold onto the OEM hardware and
plastic bracket.
4.
FOG LIGHT ASSEMBLY (DS)
7mm
9
10
11
12
Mount the S2’s with hardware as shown below. The S2 closest to the engine should
be mounted ~35/64” away from the nearest edge of the bracket. The other S2
should be mounted ~53/64” away from the nearest edge. Using the
7mm socket
,
with extension, and the OEM hardware attach the Baja Designs bracket to the OEM
plastic bracket in all available mounting
locations.
5.
Take this moment to make sure the S2 resists
rotational and up down movement. The S2
should still be able to be adjusted with force.
Refer back to
Step 4, 3, & 2
to install the Assembly.
FOG POCKET FRONT VIEW
13
14
H11 Connector
Enlarged for detail
Pin the
H11
Splitter with the polarity shown below. Plug the Baja Designs Splitter
into the pair of lights. Then, plug the
H11
connector on the end of the splitter into
original fog light plug (H11). Tug on the connection. Test that the lights turn on.
Refer to
Step 1
and re-assemble the inner fender liner. Repeat on the passenger
side.
6.
2 Pin Wiring Polarity
POS (RED)
NEG (BLK)
PIN B
PIN A
In select trims, the fog light will turn on when rotating the steering wheel past a
certain point in non off-road environments. Aim the lights downward to avoid
blinding drivers.
7.
Thank you for choosing
BD Coozie :)
3.
1
2
Grab a cold
one. You
deserve it!
Behind the grille kit!
Your Car
REMOVE THESE BOLTS
Position yourself under the truck. Remove the
bumper bolts on the back side of the bumper in
the arrowed positions below.
1.
16
18
17
1/4”-20 x 1.375” Bolt
16
1/4”-20 x 0.25” Bolt
17
1/4” Washer
18
Locate this region when behind the bumper. Landmarks are indicated
on the image below. The bumper bolt is located behind the Bumper
Support Strut.
2.
Driver Side
Tow Hook
Bumper Support
Strut
Driver Side
Attach the bracket to light bar as shown to the left. Then, replace the OEM
bumper bolts with the hardware shown in region . Finally, adjust the bar so
that the center of the lightbar is centered between the bumper parking sensors.
3.
19
1/4” Nylock Nut
1/4” Washer
1/4” Washer
1/4-20 x 1.75 Bolt
19
Adjust the lightbar forward and slightly
downward. Tighten all hardware to fix
in place. Place respective leads of relay
harness onto battery terminals, add
the extension harness, and finally plug
into the lightbar. Remove button switch.
Locate the rubber boot on the Driver
Side, make incision and feed the switch
through the firewall. Re-attach switch.
Enjoy the lumens!
4.
Reverse Kit
Exhaust
UNDER REAR BUMPER VIEW (DS)
The Light Goes Here!
1/4”-20 x 5/8” Bolt
6mm Washer
1/4” Nylock Nut
Remove the OEM screw at the arrowed location. Orient the bracket as
shown in region . Assemble the light with the S2 hardware to the
bracket. Adjust the bracket away from the exhaust tip as desired.
1.
Repeat on the passenger side. Plug in the 2 pin
splitter to both lights. Then, plug in the wire tap
harness. Pull or cut back sheathing on the
Trailer Socket behind the bumper. Use the wire
tap on the Center Wire. There is a diagram on
the Trailer Socket cover shown on the right.
Ground the wire tap harness to truck frame.
2.
20
21
22
22
20
Trailer Socket
21
19
15
