Dodge 2014 Ram 1500 Owner'S Manual Download Page 114 | Manualshive

Page: 114 / 360

background image

CAUTION!

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to the
negative post. Battery posts are marked (+) positive
and negative (-) and are identified on the battery
case. Also, if a “fast charger” is used while the battery
is in vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do not
use a “fast charger” to provide starting voltage.

WARNING!

Battery posts, terminals, and related accessories con-
tain lead and lead compounds. Always wash hands
after handling the battery.

Cooling System

WARNING!

You or others can be badly burned by hot engine
coolant (antifreeze) or steam from your radiator. If
you see or hear steam coming from under the hood,
do not open the hood until the radiator has had time
to cool. Never try to open a cooling system pressure
cap when the radiator is hot.

Engine Coolant Checks

Check the engine coolant (antifreeze) protection every 12
months (before the onset of freezing weather, where
applicable). If the engine coolant (antifreeze) is dirty or
rusty in appearance, the system should be drained,
flushed and refilled with fresh coolant. Check the front of
the A/C condenser (if equipped) or radiator for any
accumulation of bugs, leaves, etc. If dirty, clean by gently

112

MAINTAINING YOUR VEHICLE

«
...
112
113
114
115
116
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: U.S. General Pages: 5

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Westin Pages: 3

Brand: Jackco Pages: 11

Brand: Porsche Pages: 144

Brand: tams elektronik Pages: 44

Brand: Softride Pages: 4

Brand: true-i Pages: 11

Brand: Buick Pages: 161

Brand: Saab Pages: 288

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands