Dodge 2014 Ram 1500 Owner'S Manual Download Page 225 | Manualshive

Page: 225 / 360

background image

For ambient temperatures below –20°F (-29°C), engine
block heater usage is required.

DIESEL EXHAUST BRAKE (ENGINE BRAKING)

The purpose of the exhaust brake (engine braking) fea-
ture is to supply negative (braking) torque from the
engine. Typically, the engine braking is used for, but not
limited to, vehicle towing applications where vehicle
braking can be achieved by the internal engine power,
thereby sparing the mechanical brakes of the vehicle.

Benefits of the exhaust brake are:

•

vehicle driving control

•

reduced brake fade

•

longer brake life

•

faster cab warm-up

The exhaust brake feature will only function when the
driver toggles it on by pushing the exhaust brake button
until the

⬙

Exhaust Brake Indicator

⬙

is illuminated. Nor-

mal (Full Strength) exhaust brake mode is indicated by a
yellow

⬙

Exhaust Brake Indicator

⬙

.

Exhaust Brake Switch

4

STARTING AND OPERATING

223

«
...
223
224
225
226
227
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: EAL Pages: 4

Brand: RaceChip Pages: 20

Brand: Whispbar Pages: 15

Brand: NanoCam Plus Pages: 32

Brand: RBO Pages: 15

Brand: Yakima Pages: 12

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: Kleinn Pages: 8

Brand: Porsche Pages: 146

Brand: Alfa Romeo Pages: 268

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 17

Brand: MBW Pages: 40

Brand: Bazooka Pages: 2

Brand: N2MB Racing Pages: 13

Brand: Westin Pages: 9

Brand: P-Charge Pages: 16

Brand: PROUSER Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands