Dodge 2014 Ram 1500 Owner'S Manual Download | Manualshive

Page: 305 / 360

background image

CAUTION!

•

Diesel fuel will damage blacktop paving surfaces.
Drain the filter into an appropriate container.

•

Do not prefill the fuel filter when installing a new
fuel filter. There is a possibility debris could be
introduced into the fuel filter during this action. It
is best to install the filter dry and allow the in-tank
lift pump to prime the fuel system.

1. Ensure engine is turned off.

2. Place drain pan under the fuel filter drain hose.

3. Open the water drain valve 1/4 turn counterclockwise

and completely drain fuel and water into the ap-
proved container.

4. Close the water drain valve.

5. Remove lid using a socket or strap wrench. Rotate

counterclockwise for removal. Remove used o-ring
and discard it.

6. Remove the used filter cartridge from the housing and

dispose of according to your local regulations.

7. Wipe clean the sealing surfaces of the lid and housing.

8. Install new o-ring back into ring groove on the filter

housing and lubricate with clean engine oil.

9. Remove new filter cartridge from plastic bag and

install into housing.

NOTE:

Do not remove cartridge from bag until you reach

this step in order to keep cartridge clean.

10. Push down on the cartridge to ensure it is properly

seated.

Do not pre-fill the filter housing with fuel.

11. Install lid onto housing and tighten to 22.5 ft lbs (30.5

N.m). Do not overtighten the lid.

6

MAINTAINING YOUR VEHICLE

303

«
...
303
304
305
306
307
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: UltraGauge Pages: 55

Brand: Prorack Pages: 14

Brand: Vintage Air Pages: 28

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Brand: Subaru Pages: 99

10-8002-C11670C

Brand: Saleen Pages: 17

StreetLine Series

Brand: SAAS Pages: 4

Calispace Ocean 80

Brand: Calitop Pages: 5

Brand: Baja Designs Pages: 5

Brand: PAC Pages: 14

Brand: Kolpin Pages: 3

Brand: Toyota Pages: 636

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: Power Acoustik Pages: 4

Brand: Mercedes-Benz Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands