Dodge 2014 Ram 1500 Owner'S Manual Download Page 150 | Manualshive

Page: 150 / 360

background image

To Enter Remote Start Mode

Press and release the REMOTE START button
on the RKE transmitter twice, within five sec-
onds. The parking lights will flash and the horn
will chirp twice (if programmed). In cold am-

bient temperature conditions, the diesel vehicle may
delay crank up to 30 seconds for the fuel and grid heater.
Once the vehicle has started, the engine will run for 15
minutes.

NOTE:

•

The park lamps will turn on and remain on during
Remote Start mode.

•

For security, power window and power sunroof op-
eration (if equipped) are disabled when the vehicle is
in the Remote Start mode.

•

The engine can be started two consecutive times (two
15-minute cycles) with the RKE transmitter. However,
the ignition switch must be cycled to the ON position
before you can repeat the start sequence for a third
cycle.

To Exit Remote Start Mode Without Driving The
Vehicle

Press and release the REMOTE START button one time or
allow the engine to run for the entire fifteen minute cycle.

NOTE:

To avoid unintentional shut downs, the system

will disable the one time press of the REMOTE START
button for two seconds after receiving a valid Remote
Start request.

To Exit Remote Start Mode And Drive The Vehicle

To exit Remote start Mode and Drive the vehicle Before
the end of the 15-minute cycle, press and release the
unlock button on the RKE transmitter to unlock the door

148

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
148
149
150
151
152
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Laser Pages: 8

Brand: Vauxhall Pages: 199

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: Ford Pages: 2

Brand: Audiovox Pages: 24

Brand: Mercedes-Benz Pages: 2

Brand: Westin Pages: 2

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: Hyundai Pages: 11

Brand: iArmor Pages: 6

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Toyota Pages: 497

Brand: Saab Pages: 9

Brand: Acura Pages: 7

Brand: Uniden Pages: 16

Brand: RAWLINK Pages: 25

Brand: TEINHOF Pages: 2

Brand: Saab Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands