Dodge 2014 Ram 1500 Owner'S Manual Download Page 255

Page: 255 / 360

ADDING FUEL — 2500/3500 DIESEL MODELS

1. Open the fuel filler door.

1 — Diesel Exhaust Fluid Fill Location
2 — Diesel Fuel Fill Location

NOTE:

There is no fuel filler cap. A flapper door inside

the filler pipe seals the system.

2. Insert the fuel nozzle fully into the filler pipe – the

nozzle opens and holds the flapper door while refuel-
ing.

3. Fill the vehicle with fuel – when the fuel nozzle

“clicks” or shuts off the fuel tank is full.

4. Remove the fuel nozzle and close the fuel door.

Emergency Fuel Can Refueling

Most fuel cans will not open the flapper door.

A funnel is provided to open the flapper door to allow
emergency refueling with a fuel can.

Diesel Fuel And Diesel Exhaust Fluid Fill Location

STARTING AND OPERATING

253

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands

Dodge 2014 Ram 1500, Owner'S Manual

Search results

Summary of Contents for 2014 Ram 1500

Reviews:

Related manuals for 2014 Ram 1500

Brands by name

Popular brands