Dodge 2014 Ram 1500 Owner'S Manual Download Page 70 | Manualshive

Page: 70 / 360

background image

Do Not Operate The Engine With Failed Parts

All engine failures give some warning before the parts
fail. Be on the alert for changes in performance, sounds,
and visual evidence that the engine requires service.
Some important clues are:

•

engine misfiring or vibrating severely

•

sudden loss of power

•

unusual engine noises

•

fuel, oil or coolant leaks

•

sudden change, outside the normal operating range, in
the engine operating temperature

•

excessive smoke

•

oil pressure drop

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the heater
cord to a ground-fault interrupter protected 110–115 Volt
AC electrical outlet with a grounded, three-wire exten-
sion cord.

Its use is recommended for environments that routinely
fall below -10°F (-23°C). It should be used when the
vehicle has not been running for long periods of time and
should be plugged in two hours prior to start. Its use is
required for cold starts with temperatures under -20°F
(-28°C).

To ensure reliable starting at these temperatures, use of
an externally powered electric engine block heater (avail-
able from your authorized dealer) is recommended.

68

STARTING AND OPERATING

«
...
68
69
70
71
72
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Mazda Pages: 4

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

Brand: Dodge Pages: 24

Brand: UAZ Pages: 90

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

Brand: v.LOGiC Pages: 22

Brand: APS Pages: 3

2010 Challenger SRT

Brand: Dodge Pages: 444

Brand: Mercedes-Benz Pages: 398

Brand: Maserati Pages: 37

Advanced Million Color

Brand: LedGlow Pages: 4

Brand: Chevrolet Pages: 324

Brand: Nav TV Pages: 6

Brand: v.link Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands