Dodge 2014 Ram 1500 Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 360

background image

ENGINE BREAK-IN RECOMMENDATIONS

The diesel engine does not require a break-in period due
to its construction. Normal operation is allowed, provid-
ing the following recommendations are followed:

•

Warm up the engine before placing it under load.

•

Do not operate the engine at idle for prolonged
periods.

•

Use the appropriate transmission gear to prevent
engine lugging.

•

Observe vehicle oil pressure and temperature indica-
tors.

•

Check the coolant and oil levels frequently.

•

Vary throttle position at highway speeds when carry-
ing or towing significant weight.

NOTE:

Light duty operation such as light trailer towing

or no load operation will extend the time before the
engine is at full efficiency. Reduced fuel economy and
power may be seen at this time.

The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
The recommended viscosity and quality grades are
shown under “Fluids, Lubricants and Genuine Parts”,
under “Maintaining Your Vehicle” in this manual. NON-
DETERGENT OR STRAIGHT MINERAL OILS MUST
NEVER BE USED.

14

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
14
15
16
17
18
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: AA Products Pages: 8

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: Volvo Pages: 19

Brand: Buick Pages: 428

Brand: Ecco Pages: 9

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: r.LiNK Pages: 21

Brand: v.link Pages: 19

Brand: Honda Pages: 268

Brand: Lock'er Down Pages: 2

FreshSesh PowderHound

Brand: Yakima Pages: 18

Brand: Scion Pages: 24

Brand: Dodge Pages: 543

Brand: Kia Pages: 4

Brand: Acewell Pages: 7

2005 HIGHLANDER

Brand: Toyota Pages: 423

Brand: 4x4Tough Pages: 8

Brand: Lakewood Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands