Dodge 2014 Ram 1500 Owner'S Manual Download Page 309 | Manualshive

Page: 309 / 360

background image

CAUTION!

Due to lack of lubricants in alcohol or gasoline, the
use of these fuels can cause damage to the fuel
system.

NOTE:

•

A maximum blend of 5% biodiesel, meeting ASTM
specification D-975 may be used with your Cummins®
diesel engine. (Chassis Cab models not configured
with B20 capability.)

•

A maximum blend of 20% biodiesel, meeting ASTM
specification D-7467 may be used with your Cum-
mins® diesel engine. (Pickup models and Chassis Cab
models configured with B20 capability.)

•

Use of biodiesel mixture in excess of 20% can nega-
tively impact the fuel filter’s ability to separate water
from the fuel, resulting in high pressure fuel system
corrosion or damage.

•

Ethanol blends are not recommended or approved for
use with your Cummins® diesel engine.

•

In addition, commercially available fuel additives are
not necessary for the proper operation of your Cum-
mins® diesel engine.

Intervention Regeneration Strategy — EVIC
Message Process Flow

The Cummins® diesel engine meets all EPA Heavy Duty
Diesel Engine Emissions Standards, resulting in one of
the lowest emitting diesel engines ever produced.

6

MAINTAINING YOUR VEHICLE

307

«
...
307
308
309
310
311
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: Buick Pages: 428

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 373

Brand: BrandMotion Pages: 2

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

Brand: Park-Daddy Pages: 22

Brand: Subaru Pages: 298

Brand: Ecco Pages: 24

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

Brand: AIS Pages: 2

Brand: Power Acoustik Pages: 4

Brand: Webasto Pages: 23

Brand: Huf Pages: 6

Brand: GYS Pages: 32

Brand: Reliant Pages: 116

transit connect 2012

Brand: Ford Pages: 299

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands