Dodge 2014 Ram 1500 Owner'S Manual Download Page 91 | Manualshive

Page: 91 / 360

background image

Towing Tips

Before setting out on a trip, practice turning, stopping
and backing the trailer up in an area away from heavy
traffic.

Automatic Transmission

The DRIVE range can be selected when towing. The
transmission controls include a drive strategy to avoid
frequent shifting when towing. However, if frequent
shifting does occur while in DRIVE, select TOW/HAUL
mode or select a lower gear range (using the Electronic
Range Select (ERS) shift control).

NOTE:

Using TOW/HAUL mode or selecting a lower

gear range (using the ERS shift control) while operating
the vehicle under heavy loading conditions will improve
performance and extend transmission life by reducing
excessive shifting and heat build up. This action will also
provide better engine braking.

When towing a loaded trailer up steep grades at low
speeds (20 mph [32 km/h] or below), holding your
vehicle in first gear (using the ERS shift control) can help
to avoid transmission overheating.

Tow/Haul Mode

To reduce potential for automatic transmission overheat-
ing, activate TOW/HAUL mode when driving in hilly
areas, or select a lower gear range (using the Electronic
Range Select (ERS) shift control) on more severe grades.

Electronic Speed Control — If Equipped

•

Do not use in hilly terrain or with heavy loads.

•

When using the speed control, if you experience speed
drops greater than 10 mph (16 km/h), disengage until
you can get back to cruising speed.

•

Use speed control in flat terrain and with light loads to
maximize fuel efficiency.

4

STARTING AND OPERATING

89

«
...
89
90
91
92
93
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Brand: AAMP of America Pages: 6

Brand: Yakima Pages: 8

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: Porsche Pages: 195

Brand: Phonocar Pages: 2

Brand: Thule Pages: 12

Brand: Jeep Pages: 380

Brand: Quadratec Pages: 8

Brand: Whispbar Pages: 17

Brand: CrimeStopper Pages: 1

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: Brigade Pages: 12

Multi Vehicle Mount MVM-35-05

Brand: Bracketron Pages: 4

Brand: AUTOTECH Pages: 4

Brand: Magneti Marelli Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands