Dodge 2014 Ram 1500 Owner'S Manual Download Page 212 | Manualshive

Page: 212 / 360

background image

2. While the

⬙

Wait To Start” telltale is on, the EVIC will

additionally display a gauge or bar whose initial
length represents the full

⬙

Wait To Start

⬙

time period.

Its length will decrease until it disappears when the

⬙

Wait To Start

⬙

time has elapsed.

CAUTION!

If the “Water in Fuel Indicator Light” remains on, DO
NOT START engine before you drain the water from
the fuel filters to avoid engine damage. Refer to
“Maintenance Procedures/Draining Fuel/Water Sepa-
rator Filter” in “Maintaining Your Vehicle” for fur-
ther information.

3. After the “Wait To Start” telltale goes off, turn the

ignition switch to the START position. Do not press the
accelerator during starting.

CAUTION!

Do not crank engine for more than 15 seconds at a
time or starter motor damage may result. Turn the
ignition switch to the OFF position and wait at least
two minutes for the starter to cool before repeating
start procedure.

4. After engine start-up, check that the oil pressure

warning light has turned off.

5. Allow the engine to idle about three minutes until the

manifold heaters have completed the post-heat cycle.

6. Release the parking brake and drive.

NOTE:

•

Engine idle speed will automatically increase to 1,000
RPM and engage the Variable Geometry Turbocharger at
low coolant temperatures to improve engine warm-up.

210

STARTING AND OPERATING

«
...
210
211
212
213
214
...
»

Summary of Contents for 2014 Ram 1500









































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Ram 1500

Multiple G9F18 AU000

Brand: Genesis Pages: 3

1973 Convertible

Brand: Volkswagen Pages: 80

StreetLine Series

Brand: SAAS Pages: 4

Brand: Quadratec Pages: 12

Brand: Xhorse Pages: 48

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: GARO Pages: 15

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Rugged Ridge Pages: 2

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: Edelbrock Pages: 4

Brand: Prorack Pages: 13

Brand: Butts of Bawtry Pages: 2

LineCast Auto FM

Brand: Belkin Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands